Skip to main content
Civil & Structural EngineeringPublished 2026-04-2014 min read

Shear Force and Bending Moment Diagrams (SFD & BMD): Step-by-Step Analytical Procedures

A rigorous engineering guide to constructing Shear Force Diagrams (SFD) and Bending Moment Diagrams (BMD). Details standard deformation sign conventions, differential equilibrium relationships (w = -dV/dx, V = dM/dx), the Graphical Area Method, singularity functions, the distinction between stationary points and absolute extrema, contraflexure points, and an end-to-end multi-load overhanging beam benchmark.

Author: Md. Nur Islam•Founder of EngiVanta

When external loads act on a structural beam—whether gravitational dead loads, moving vehicular traffic, or lateral wind pressure—the beam maintains structural integrity by developing internal shear forces and bending moments across every cross-section. Solving for external reactions confirms global static equilibrium (sum F = 0, sum M = 0), but reveals nothing about whether individual cross-sections will crack, yield, buckle, or fracture.

To proportion structural elements safely, engineers construct two interrelated diagnostic plots along the beam span (x): the Shear Force Diagram (SFD), plotting internal transverse shear V(x) that governs web sizing and transverse stirrup spacing, and the Bending Moment Diagram (BMD), plotting internal flexural couple M(x) that dictates flange dimensions, section modulus, and longitudinal steel placement.

A frequent source of errors in structural mechanics is confusing static coordinate directions with internal deformation sign conventions, or assuming that zero shear automatically identifies the global maximum moment. This guide establishes the differential calculus and graphical area principles governing beam equilibrium, clarifies stationary points versus boundary extrema, and works through an exact 8.0 m multi-load overhanging beam benchmark.

1. Internal Deformation Sign Conventions & Beam Supports

In structural mechanics, internal force diagrams must follow standard deformation conventions, independent of external coordinate axis choices:

• Positive Shear Force (+V): Produces clockwise rotation of the isolated beam segment. On a section cut looking at the left segment, positive shear acts downward; looking at the right segment, positive shear acts upward.

• Positive Bending Moment (+M) — Sagging: Produces concave-upward curvature (tension in bottom fibers, compression in top fibers). On a cut face looking at the left portion, positive moment acts counter-clockwise.

• Negative Bending Moment (-M) — Hogging: Produces concave-downward curvature (tension in top fibers, compression in bottom fibers). Common over interior supports of continuous beams and cantilevers.

2. Differential Relationships Between Load, Shear, and Moment

Considering an infinitesimal beam element of length dx subjected to downward transverse distributed load w(x), vertical and moment equilibrium yield the governing differential equations of flexure:

CE Toolbox: Structural Beam Shear & Moment Analyzer

ce-str-01

Evaluate reactions, shear forces, bending moments, and deflections for simply supported and cantilever beams in CE Toolbox.

Governing Formulation:
dV(x)/dx = -w(x) and dM(x)/dx = V(x)

The Load-Shear Theorem

The slope of the shear force diagram at any point equals the negative of distributed load intensity (-w). If no load acts on a segment (w = 0), shear is constant (horizontal line). Under a uniform load (w = const), shear is a straight line sloping downward at rate -w. Under a triangular load, shear is a second-degree parabola.

The Shear-Moment Theorem & The Graphical Area Method

The slope of the bending moment diagram at any point equals the internal shear force V(x). Integrating between any two span positions x1 and x2 yields the Graphical Area Method:

• Change in Shear: V(x2) - V(x1) = -[Area under load w(x) between x1 and x2]

• Change in Moment: M(x2) - M(x1) = [Signed area under shear V(x) between x1 and x2]

M(x2) - M(x1) = ∫[x1 to x2] V(x) dx

3. Stationary Points, Global Extrema, and Points of Contraflexure

Critical distinctions separate rigorous structural mechanics from superficial memorization:

1. Zero-Shear Locations: Setting V(x) = 0 identifies a stationary point (horizontal tangent, dM/dx = 0). While it frequently locates local sagging peaks, negative hogging moments over interior supports or fixed ends often exceed the mid-span moment in absolute magnitude. Designers must evaluate all stationary points, step discontinuities, and support locations to determine the absolute governing moment (|M|_max).

2. Point of Contraflexure (Inflection Point): A location where the bending moment is zero (M(x) = 0) and reverses sign between sagging and hogging. Curvature flips direction (d²v/dx² = 0) and normal bending stress drops to zero. Points of contraflexure indicate where rebar can be safely curtailed or shifted between faces. It is not where shear is zero; shear force is often high at an inflection point.

3. Concentrated Load Step Jumps: A downward point load P induces an instantaneous downward vertical step in shear (-P) and a sharp kink in moment. A concentrated couple M0 introduces an instantaneous vertical step in moment (+M0) with zero effect on shear.

4. Comprehensive Worked Benchmark: Multi-Load Overhanging Beam

Analyze an 8.0 m structural steel overhanging beam:

• Total Span: L = 8.000 m. Pin support A at x = 0.0 m, Roller support B at x = 6.000 m, Cantilever overhang from x = 6.0 m to x = 8.000 m (overhang length = 2.0 m).

• Loading: Uniform distributed load w = 12.000 kN/m across the entire 8.0 m beam; concentrated point load P = 30.000 kN at x = 3.000 m; concentrated tip load Q = 20.000 kN at x = 8.000 m.

Step 1 — Support Reactions via Static Equilibrium:

• Total downward gravity load: (12 · 8) + 30 + 20 = 96 + 50 = 146.000 kN.

• Moments about A: 6.0 · RB - (12 · 8 · 4) - (30 · 3) - (20 · 8) = 0 => 6 · RB - 634.0 = 0 => RB = 105.6667 kN (upward).

• Vertical equilibrium: RA = 146.0 - 105.6667 = 40.3333 kN (upward).

Step 2 — Piecewise Equations by Interval:

• Interval 1 (0 ≤ x < 3.0 m): V1(x) = 40.3333 - 12 x. V(0⁺) = +40.333 kN, V(3⁻) = +4.333 kN. M1(x) = 40.3333 x - 6 x². M(0) = 0, M(3) = +67.000 kN·m.

• Interval 2 (3.0 < x < 6.0 m): Under load P, shear steps down: V2(3⁺) = +4.3333 - 30 = -25.6667 kN. V2(x) = 10.3333 - 12 x. V(6⁻) = -61.6667 kN. M2(x) = -6 x² + 10.3333 x + 90.0. M(3) = +67.000 kN·m, M(6) = -64.000 kN·m.

• Zero Shear & Maximum Sagging Moment: Shear crosses zero at step discontinuity x = 3.000 m. Maximum positive sagging moment M_max,pos = +67.000 kN·m.

• Point of Contraflexure: Setting M2(x) = 0: 6 x² - 10.3333 x - 90 = 0. Quadratic root: x = (10.3333 + sqrt(106.78 + 2160)) / 12 = (10.3333 + 47.6107) / 12 = 4.8287 m ≈ 4.829 m.

• Interval 3 (6.0 < x ≤ 8.0 m): At support B, RB steps shear up: V3(6⁺) = -61.6667 + 105.6667 = +44.000 kN. V3(x) = 116.0 - 12 x. V(8⁻) = +20.000 kN. At x = 8⁺, tip load Q = 20 kN closes shear to 0.000 kN. M3(6) = -64.000 kN·m (Maximum negative hogging moment), M3(8) = 0.000 kN·m (Exact boundary closure).

Step 3 — Area Method Cross-Check:

• Segment 1 (0 to 3 m): ΔM = ((40.3333 + 4.3333) / 2) · 3 = +67.000 kN·m => M(3) = +67.000 kN·m.

• Segment 2 (3 to 6 m): ΔM = ((-25.6667 + -61.6667) / 2) · 3 = -131.000 kN·m => M(6) = 67.000 - 131.000 = -64.000 kN·m.

• Segment 3 (6 to 8 m): ΔM = ((44.000 + 20.000) / 2) · 2 = +64.000 kN·m => M(8) = -64.000 + 64.000 = 0.000 kN·m.

Position x (m)Key Feature / DiscontinuityShear Force V(x) (kN)Bending Moment M(x) (kN·m)Mathematical Meaning
0.000⁻Left of Support A0.0000.000Initial boundary
0.000⁺Reaction RA = +40.333 kN+40.3330.000Upward step in shear
1.500Quarter Span Point+22.333+47.000Parabolic sagging curve
3.000⁻Left of Point Load P+4.333+67.000Moment slope approaches +4.33
3.000⁺Under Point Load P = 30 kN-25.667+67.000Global Maximum Sagging Moment
4.829Point of Contraflexure-47.6110.000Inflection point (curvature flips)
6.000⁻Left of Support B-61.667-64.000Global Maximum Hogging Moment
6.000⁺Reaction RB = +105.667 kN+44.000-64.000Upward step jump in shear
7.000Midpoint of Overhang+32.000-26.000Hogging cantilever parabolic curve
8.000⁻Inside Cantilever Tip+20.0000.000Shear equals tip load Q
8.000⁺Tip Load Q = 20 kN0.0000.000Exact closure to zero

Frequently Asked Questions

A positive bending moment produces sagging curvature, creating tension in bottom fibers and compression in top fibers. A negative bending moment produces hogging curvature, creating tension in top fibers and compression in bottom fibers (typical over continuous supports and cantilevers).

Standard Citations & Technical References

NI

Md. Nur Islam

Founder of EngiVanta

Founder of EngiVanta. Directing platform architecture, numerical calculation standards, and engineering publications across civil and mechanical domains.