Skip to main content
Mechanical Machine Design & FastenersPublished 2026-04-1810 min read

Shaft Design for Combined Torsion, Bending, and Fatigue: ASME B106.1M & Goodman Criteria

Power transmission shafts experience combined cyclic reversed bending, steady torsion, and stress concentrations. This guide details Marin endurance limit modifications, DE-Goodman, ASME Elliptic, and Soderberg failure criteria, keyway notch factors, and a complete 45 kW electric drive shaft benchmark.

Author: Md. Nur Islam•Founder of EngiVanta

Transmission shafts are the mechanical backbone of rotary machinery, transmitting power between motors, gearboxes, belt pulleys, and fluid impellers. In virtually every real-world application, a rotating shaft is subjected to simultaneous fluctuating multiaxial stresses: reversed bending stress from transverse belt or gear loads, and steady torsional shear stress from transmitted power.

As the shaft rotates, any surface fiber transitions cyclically from peak tension to peak compression every revolution (fully reversed fatigue, R = -1). Meanwhile, transmitted torque generates steady shear stress.

Historical elastic failures and fatigue disasters led to the development of standardized fatigue sizing protocols. The ASME Standard B106.1M (Design of Transmission Shafting) and the Distortion Energy (DE) Goodman and ASME Elliptic formulations provide closed-form equations that directly determine the minimum required shaft diameter to prevent both high-cycle fatigue failure and static yield during transient shock overloads.

This guide presents the multiaxial fatigue formulation, Marin endurance modifications, keyway stress concentration factors, and a worked benchmark for a 45 kW motor drive shaft.

1. Multiaxial Stress State in a Rotating Shaft

For a solid circular shaft of diameter d subjected to alternating bending moment Ma, mean bending moment Mm, alternating torque Ta, and mean torque Tm:

Governing Formulation:
σa = (32 · Kf · Ma) / (π · d³) | τm = (16 · Kfs · Tm) / (π · d³)

Von Mises Equivalent Alternating and Mean Stresses

For a shaft rotating at constant speed under steady transverse loads, bending is purely reversed (Mm = 0) and steady torque has zero alternating component (Ta = 0). Applying Distortion Energy theory yields:

σa' = (32 · Kf · Ma) / (π · d³) | σm' = (16 · √3 · Kfs · Tm) / (π · d³)

2. Marin Endurance Limit Modification (Se)

The endurance limit of the actual shaft component (Se) is derived from the ideal polished rotating-beam laboratory specimen limit (Se' = 0.5 · Sut for steel ≤ 1400 MPa) using the Marin formulation:

Governing Formulation:
Se = ka · kb · kc · kd · ke · Se'
Table 1: Marin fatigue modification factors for steel drive shafts.
Marin FactorSymbolEngineering Formulation / Baseline ValuesBenchmark Value
Surface Conditionkaka = a · Sut^b (For cold-drawn steel: a = 4.51, b = -0.265 in MPa)0.822
Size Factorkbkb = 1.24 · d^(-0.107) for 2.79 mm ≤ d ≤ 51 mm0.825
Load Factorkckc = 1.00 for bending (Distortion Energy handles shear conversion)1.000
Temperature Factorkdkd = 1.00 for operating temperature T ≤ 450°C1.000
Reliability Factorkeke = 0.814 for 99% reliability (0.897 for 90%, 0.753 for 99.9%)0.814

3. Closed-Form Shaft Diameter Sizing Equations

Setting the operating stress state on the fatigue failure boundary with design safety factor n yields direct closed-form solutions for minimum shaft diameter d:

DE-Goodman Criterion (Standard Industrial Baseline)

The DE-Goodman criterion uses ultimate tensile strength (Sut) on the mean stress axis:

d = { (16 · n / π) · [ (2 · Kf · Ma / Se) + (√3 · Kfs · Tm / Sut) ] }^(1/3)

DE-ASME Elliptic Criterion (Basis of ASME B106.1M)

The ASME Elliptic criterion connects Se on the alternating axis with yield strength Sy on the mean axis using an elliptical quadrant, preventing over-conservative shaft sizing:

d = { (16 · n / π) · √[ (2 · Kf · Ma / Se)² + 3 · (Kfs · Tm / Sy)² ] }^(1/3)

4. Stress Concentration Factors (Kf, Kfs) at Shaft Features

Local geometry changes amplify nominal stress via fatigue notch sensitivity q: Kf = 1 + q·(Kt - 1).

Table 2: Fatigue stress concentration factors at common shaft discontinuities.
Shaft Feature / DiscontinuityBending Factor KfTorsion Factor KfsDesign Note
Profile End-Mill Keyway2.01.6Abrupt end corners; highest stress concentration
Sled-Runner Keyway1.61.3Gradual cutter runout; superior fatigue life
Shoulder Fillet — Sharp (r/d = 0.02)2.51.8Bearing seating with insufficient fillet radius
Shoulder Fillet — Well-rounded (r/d = 0.10)1.51.2Optimized transition fillet
Retaining Ring (Snap-Ring) Groove3.02.4Severe notch; keep away from high-bending locations

5. Worked Industrial Benchmark: 45 kW Fan Drive Shaft

A solid steel drive shaft transmits power from an electric motor to an industrial ventilation fan:

• Power: P = 45.0 kW (60.3 hp) at N = 1200 rpm (ω = 125.66 rad/s) • Reversed Bending Moment: Ma = 520.0 N·m (Mm = 0) • Material: AISI 1045 Cold-Drawn Carbon Steel (Sut = 630 MPa, Sy = 530 MPa, Se' = 315 MPa) • Geometry: Profile end-mill keyway (Kf = 2.0, Kfs = 1.6) • Target: 99% reliability (ke = 0.814), safety factor n = 2.0

Steel Weight & Bar Stock Calculator

steel-weight

Determine round bar shaft mass, cross-sectional area, and volume.

Mechanical Engineering Toolbox (ME Toolbox)

me-toolbox

Run shaft torsional shear, combined stress, and beam deflection calculations.

Step 1: Steady Torque & Modified Endurance Limit

• Steady Mean Torque: Tm = P / ω = 45,000 / 125.6637 = 358.10 N·m (Ta = 0) • Modified Endurance Limit: Se = 0.822 · 0.825 · 1.0 · 1.0 · 0.814 · 315.0 MPa = 174.05 MPa (1.7405 × 10⁸ Pa)

Step 2: Shaft Diameter per DE-Goodman and ASME Elliptic

• Alternating Bending Term: (2 · Kf · Ma) / Se = (2 · 2.0 · 520.0) / (1.7405 × 10⁸) = 1.1951 × 10⁻⁵ m³ • Goodman Torsional Term: (√3 · Kfs · Tm) / Sut = (1.732 · 1.6 · 358.10) / (6.30 × 10⁸) = 1.5753 × 10⁻⁶ m³ • Sum of Terms: 1.1951 × 10⁻⁵ + 1.5753 × 10⁻⁶ = 1.3526 × 10⁻⁵ m³ • DE-Goodman Diameter: d = [ (32 / π) · 1.3526 × 10⁻⁵ ]^(1/3) = (1.3777 × 10⁻⁴)^(1/3) = 0.05165 m = 51.65 mm • ASME Elliptic Diameter: d = { (32 / π) · √[ (1.1951 × 10⁻⁵)² + (1.8725 × 10⁻⁶)² ] }^(1/3) = 0.04976 m = 49.76 mm

d_Goodman = 51.65 mm | d_ASME_Elliptic = 49.76 mm

Step 3: Specification Selection & Static Yield Check

• Standard Metric Bearing Bore: Specify d = 55.0 mm (Matches standard 6211 deep-groove ball bearing bore per ISO 15 boundary dimensions). • Actual Fatigue Safety Factor: n = 2.41 at d = 55.0 mm. • Static Yield Safety Factor under 150% peak startup shock: σvM = 104.2 MPa << Sy = 530 MPa (Static safety factor > 5.0).

Frequently Asked Questions

In a shaft transmitting constant power under steady belt or gear radial loads, the bending moment plane remains fixed in space while the shaft rotates. Each outer fiber therefore cycles from peak tension to peak compression on every revolution (fully reversed fatigue, R = -1), whereas steady transmitted torque creates constant mean shear stress.

Standard Citations & Technical References

NI

Md. Nur Islam

Founder of EngiVanta

Founder of EngiVanta. Directing platform architecture, numerical calculation standards, and engineering publications across civil and mechanical domains.